The pins inside a pin-tumbler lock are small two-piece stacks that stop the lock's plug, the part that turns with the key, from rotating. Springs push each stack down across the seam between the plug and the fixed housing around it. The correct key lifts every stack so its split lands exactly on that seam, called the shear line, and only then can the plug turn.
The parts inside a keyed cylinder
A standard keyed lock has a cylinder, the round unit that takes the key. The cylinder's outer body, the housing, stays fixed. Inside the housing sits the plug, the smaller round piece with the keyhole in its face, and the plug is the part that turns. A row of holes runs through the plug and up into the housing. Each hole holds a pin stack with a small coil spring above it. The key's blade carries a row of cuts along its edge, one cut for each stack.
What the pins do at rest and when the key goes in
- With no key, each spring presses its pin stack down so the stack reaches across the thin seam between plug and housing. Part of the stack sits on each side of the seam, and the plug cannot rotate.
- As the key slides in, the pins ride up and down over its peaks and valleys. That movement is the light clicking you sometimes feel along the blade.
- Once the key is fully inserted, each stack rests on one cut, and the depth of that cut sets how high the stack sits.
- When the split in every stack lands on the seam, called the shear line, nothing crosses it and the plug turns.
One stack crossing the seam is enough to stop the plug. The lock needs all of them lined up at once.
Why each pin stack is two pieces
A pin stack is split on purpose. The lower piece, the key pin, touches the key. The upper piece, the driver pin, sits between the key pin and the spring. The split between those two pieces is the only place a stack can separate, so at each hole the lock asks one thing: does the split land on the shear line?
Key pins come in different lengths. A long key pin needs a deep cut so it sits low enough. A short key pin needs a shallow cut. Since each position has its own length, the matching key needs its own depth at each position. The useful way to picture a key is as a row of heights read along the blade, one height per pin. Two keys that fit the same keyhole can carry very different rows.
Does the key push the pins out of the way?
A common picture is that the key shoves the pins aside. The pins never move aside. They only move up and down, and the key's job is to stop every stack at one particular height.
Too high fails as surely as too low. A cut that is too shallow lifts the stack so far that the key pin itself crosses the shear line. A cut that is too deep leaves the driver pin reaching down into the plug. Either way, that single position holds the plug still.
Most of a key's shape means nothing to the pins. The grooves along the side of the blade decide whether the key enters the keyway, the slot shaped to accept it. Once the key is inside, each pin responds only to the cut directly beneath it. A key that looks right but has one cut slightly off still leaves the cylinder locked.
What the pins explain about worn keys and rekeying
Wear changes a key's heights. Use rubs metal off the blade, so the peaks round over and the surfaces the pins rest on drop a little. A stack sitting slightly low can leave its driver pin across the shear line, and the key may turn only if you jiggle it or draw it back a touch. A copy cut from a worn key carries the same drift.
Rekeying changes the other half of the match. Rather than fitting a key to the pins, a rekey fits the pins to a new key. With new key pin lengths in the cylinder, the old key's row of heights no longer lines up and the new key's does.
The same picture helps you describe a problem. Saying the key goes in but will not turn, that it works only with some wiggling, or that the original works and the copy does not tells a locksmith far more than saying the lock is broken. If you want a lock rekeyed or checked, call Brooklyn Locksmith & Doors at (347) 357-0985.
Frequently asked questions
Does a lock with more pins always mean it is harder to defeat?
Pin count alone does not decide how hard a lock is to defeat. More pin positions allow more possible rows of key heights, so more distinct keys can exist for that lock design. How well a lock holds up against an attack depends on many other things as well, including how the cylinder is made and how the lock is mounted, so the number of pins is one detail rather than a rating.
Why can a copy of a key work poorly when it looks the same as the original?
A copied key can match the original by eye and still be off by a small amount at one cut. The pins in a pin-tumbler lock respond only to height, so that small error can leave one stack just above or below the shear line. Rough edges left on a freshly cut copy can also catch the pins as the key slides in. A copy made from another copy carries both keys' errors.
Do all keyed locks on a door use the same kind of pins?
Not all keyed locks use identical pins. Many door locks use pin-tumbler cylinders, but two of them can differ in the number of pin positions, the key pin lengths, and the keyway shape. Other keyed designs work differently, such as wafer locks, which use flat plates instead of round pin stacks. A key only lines up the pins of the cylinder its cuts were made to match.
Does rekeying replace the whole lock or only change the inside of the cylinder?
Rekeying changes only the inside of the lock cylinder. The key pins are swapped for lengths that match a new key, so every copy of the old key stops lining up at the shear line at once. The lock body, the handle or knob, and the bolt or latch are untouched by the pin change, so a rekey changes which key turns the plug, not how the bolt or latch behaves.
Need a locksmith in Brooklyn? We come to you -- 24/7.
(347) 357-0985 - Call Now