When a key goes all the way into a lock but won't turn, the cause usually sits in one of three places: the key itself, the lock cylinder, or the door and bolt being out of line with the frame. A few calm checks, changing one thing at a time, tell you which is most likely. The one thing to avoid is forcing the key, which can snap it inside the lock.
Where a key that won't turn usually gets stuck
Most door locks use a pin tumbler cylinder. Inside it is a small rotating core, called the plug, held still by spring-loaded pins. The right key lifts each pin to the height that frees the plug to turn. If the key's cuts are worn or the pins are stuck, the plug stays put even though the key slid in all the way.
Behind the plug sits a cam or tailpiece, the piece that links the cylinder to the bolt and drives the bolt in and out. If the bolt is pressed hard against the strike plate on the frame, the key won't go around even when the cylinder is healthy. The bolt has nowhere to travel.
Forcing the key fixes none of these problems. Extra twist tends to bend a key or snap it off in the keyway, which is the slot the key slides into.
What to notice, changing one thing at a time
If the key behaves the same after a change, you have ruled something out. If it behaves differently, you have a clue.
- Try a second key, ideally one that was not copied from the troublesome key.
- Notice whether the key slid in smoothly and seated fully, or caught partway. A key that stops short cannot line up the pins.
- Feel the turn. Either there is no movement at all, or the key rotates a little and then hits something firm.
- Try the same key in other doors it opens. One door failing while the rest work narrows things down.
- If you can reach the door from inside, open it and try the key with the door standing open. Then close it and try again while gently pushing or pulling the door against the frame.
The feel of the turn tells you the most. No movement at all usually means the plug never got free, which points to the key or the cylinder. A partial turn that stops means the plug rotated and something farther along resisted, which points to the bolt and the frame.
Key, cylinder, or door: how each one tends to look
The key
If a spare turns easily and one key does not, that key is the likely culprit. Sight down the blade for a bend, and look for cuts that have gone rounded and shiny.
The cylinder
When every key fails the same way, including one that worked fine last week, the cylinder is the likelier source. Dirt, worn pins, or damage inside the plug affect all keys equally. A lock that felt sticky for a while before it stopped turning also points here.
Door and bolt alignment
A key that turns with the door open but not closed is the clearest sign of alignment trouble. So is a key that turns once you lean on the door. A sagging door, a shifting frame, or a moved strike plate leaves the bolt rubbing on the edge of the strike opening.
Storefront and panic bar doors
Heavy storefront doors put a lot of load on their hinges and pivots, and a door that has dropped slightly can pin the bolt. On a door with a panic bar, the outside cylinder often drives more hardware than a house deadbolt does, so stiffness can start well away from the key.
These patterns suggest a cause rather than prove one. A door can sag and have a worn key at the same time.
Stop forcing it, then make the call
After a few gentle tries, stop. Don't slide a screwdriver, pick, or second key into the keyway, and don't tap the lock to jar it loose. If part of a key has already snapped off, leave it where it is.
A door that is open, or one you can get through another way, is not an emergency. A door that is shut and locked with no other way in is a lockout. Brooklyn Locksmith & Doors works 24/7 across Brooklyn, and you can call (347) 357-0985 for a lockout or for lock work on a home, business, or storefront door.
Before you call, have these details ready:
- Which door it is: front, back, unit, gate, or storefront
- Which key you used, and whether a second key acted the same
- What the turn felt like: no movement, or a partial turn that stopped
- Whether the door was open or closed, and whether pressure on it changed anything
- Anything you already tried, including spraying the lock or bending the key
Frequently asked questions
Can a worn key be the reason it won't turn even though it fits?
Yes. A worn key still slides in because the shape of its blade matches the keyway, but its cuts have rounded off, so the pins stop short of the height that frees the plug. A spare cut from an original key is the easiest test. Copies made from a worn key carry the same wear, and each copy of a copy drifts a little further from the original.
Is it okay to spray something in the lock to get the key turning?
Spraying whatever is handy into a lock that won't turn often backfires. Some household oils stay tacky and gather grit inside the cylinder, which can make the pins stickier over time. No spray helps a bolt that is binding on the strike plate. Note the symptoms and let a locksmith suggest what suits that lock.
Why does the key work sometimes and not other times?
When a key works only some of the time, notice when it fails. Trouble that comes and goes with the weather points to the door and frame shifting and pinching the bolt. A key that works only after jiggling points to worn key cuts or worn cylinder pins.
Does a key that won't turn mean I need a new lock?
A key that won't turn does not automatically mean a new lock. A worn key may only need replacing, and an alignment problem lives in the door or strike plate rather than the lock. Cylinder damage can call for repair, a rekey, or replacement, decided once someone sees the hardware.
Need a locksmith in Brooklyn? We come to you -- 24/7.
(347) 357-0985 - Call Now